Techni-Tool
TekBox
TekBox

TekBox TBPS01-TBWA2/40dB EMC Near-Field Probe Set + 40dB Wideband Amplifier in Wood Box, 3GHz

Our Part #20000349

Mfr Part #TBPS01-TBWA2/40dB

TekBox TBPS01-TBWA2/40dB
TekBox
TekBox

TekBox TBPS01-TBWA2/40dB EMC Near-Field Probe Set + 40dB Wideband Amplifier in Wood Box, 3GHz

Our Part #20000349

Mfr Part #TBPS01-TBWA2/40dB

$389.00EACH
Quantity on Order:31

TBPS01-TBWA2/40dB EMC Near-Field Probe Set + 40dB Wideband Amplifier

Features:

  • TBPS01-TBWA2/40dB EMC Near-Field Probe Set + 40dB Wideband Amplifier in a Wooden Box
  • Slim design for good access in between tightly spaced components
  • Shielded loops to avoid picking up common mode noise; insensitive to the human hand
  • Frequency range: 3GHz, though they can be used well beyond
  • SMB connectors to avoid twisting the RF cable when scanning DUTs

TBWA2/40dB Amplifier Specs:

  • 40dB Wideband Amplifier
  • Input / Output: 50 Ohm, SMA
  • Nominal supply Voltage: 4.5 - 5V, typ. 210mA, Mini-USB-B connector
  • Maximum supply voltage: 5.5V
  • Maximum input power: -10dBm

TBPS01 Probe Specs:

  • H20 H-Field - 170 mm Long, 20 mm Loop
  • H10 H-Field - 170 mm Long, 10 mm Loop
  • H5 H-Field - 170 mm Long, 5 mm Loop
  • E5 E-Field - 170 mm Long, 5 mm Tip

The H20, H10, H5 and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre- compliance measurements. The probes are used in the near field of sources of electromagnetic radiation. They serve to locate and identify potential sources of interference within the building blocks of electronic assemblies.

The probes act similar as wide bandwidth antennas, picking up radiated emissions from components, PCB traces, housing openings or gaps and from any other parts that could be emitting RF. The probes are usually connected to a spectrum analyzer. Scanning the probe over the surface of a PCB assembly or housing quickly identifies locations which emit electromagnetic radiation. By changing to a probe with smaller size, the origination of the emissions can be further narrowed down.

Additional applications are RF immunity tests by feeding a RF signal into the probe and radiating it into potentially susceptible circuit sections: Furthermore the probes can be used in the field of repair or debugging to track down issues in RF signal chains by contactless measurement of RF signal levels. One more application is non- invasive measurement of RF building blocks such as modulators or oscillators. Frequency, phase noise and spectral components can be measured in conjunction with a low noise pre-amplifier. The TBWA2/20dB and TBWA2/40db wideband amplifiers are connected between EMC probe and Spectrum Analyzer to increase the dynamic range of the measurements.

In The Box:

  • EMC probe set consisting of H20, H10, H5, E5
  • TBWA2/40dB 40dB Wideband Amplifier
  • 75cm SMB to SMA cable
  • 75cm SMA to N cable
  • USB cable
  • Wooden case
  • Measurement plots

BrandTekBox
IncludesProbe set: H20, H10, H5, E5; 40dB Wideband Amplifier; 75cm SMB to SMA cable; 75cm SMA to N cable; USB cable; Wooden case; Measurement plots
$389.00EACH
Quantity on Order:31